Left: Scanning electron microscopy image of the CuNW network on a copper-sprayed surface. Right: Up-close image of CuNW nanowire, which is about 60 nm in diameter, approximately 100x smaller than a human hair.
An ancient metal used for its microbial properties is the basis for a materials-based solution to disinfection.
A team of scientists from Ames National Laboratory, Iowa State University, and University at Buffalo developed an antimicrobial spray that deposits a layer of copper nanowires onto high-touch surfaces in public spaces. The spray contains copper nanowires (CuNWs) or copper-zinc nanowires (CuZnNWs) and can form an antimicrobial coating on a variety of surfaces. This research was initiated by the COVID-19 pandemic, but the findings have wider-reaching applications.
People have taken advantage of copper’s antimicrobial properties since 2400 B.C. to treat and prevent infections and diseases. It has been proven effective for inactivating viruses, bacteria, fungi, and yeasts when they are directly in contact with the metal. According to Jun Cui, a scientist at Ames Lab and one of the lead researchers on the project, “copper ion can penetrate the membrane of a virus and then insert itself into the RNA chain, and completely disable the virus from duplicating itself.”
Amidst the pandemic, “The DOE asked researchers, what can you do to help to mitigate this COVID situation?” Cui said. Ames Lab is known for work in materials science, not a field that often intersects with disease research. However, Cui’s team came up with the idea to apply copper’s antimicrobial properties to help reduce the spread of COVID.
Cui explained their idea came from a separate project they were working on, which is a copper ink designed for printing copper nanowires used in flexible electronic devices. “So the thinking is, this is ink, and I can dilute it with water or even ethanol, and then just spray it. Whatever the surface, I spray it once and coat it with a very light layer of a copper nanowire,” he said.
First the surface needs to be cleaned and disinfected, then the reformulated copper ink solution can be applied. The ideal coating should be thin enough to be transparent. The ink can be diluted with water or alcohol to make it sprayable, and it works on plastic, glass, and stainless-steel surfaces.
The team tested two types of copper ink, CuNW and CuZnNW. Compared to a plain copper disk, both inks were just as effective at disabling the virus. However, it took 40 minutes for the copper disk to disable the virus, whereas it took the copper inks only 20 minutes. The nanowires worked faster because of their greater surface area.
In a comparison between the two ink coatings, the CuNW inactivated the virus more quickly than CuZnNW during the first 10 minutes. However, CuZnNW had a more steady and sustainable release of copper ions, compared to CuNW, which makes the coating effective for a longer amount of time. Ultimately the team concluded that the CuZnNW was the best option for a sprayable copper nanowire coating for antimicrobial purposes.
Cui said that this work was important, not just because of the pandemic, but since these nanowires can protect against many different microbes, “there’s the chance that we can have a lasting impact to human society.”
Original Article: Scientists use copper nanowires to combat the spread of diseases
More from: Ames Laboratory | Iowa State University | University at Buffalo
The Latest Updates from Bing News
Go deeper with Bing News on:
Antimicrobial coating
- Nanophase Technologies Corporation (PNK:NANX) Q1 2024 Earnings Call Transcript
April 24, 2024 Nanophase Technologies Corporation isn't one of the 30 most popular stocks among hedge funds at the end of the third quarter (see the details here). Operator: Thank you for standing by, ...
- Forecasted Growth: AMEA Nanotechnology Photocatalysis Surface Coating Industry Set to Reach US$ 255.2 Million by 2033
The AMEA (Asia and Middle East and Africa) nanotechnology photocatalysis surface coating industry value is predicted to increase from US$ 85.3 million in 2023 to US$ 255.2 million by 2033. Over the ...
- FDA delivers de novo clearances to 2 novel antibacterial implant coatings
The FDA has handed out groundbreaking green lights to a pair of novel antibacterial coatings that each aim to keep implants as clean as possible during their short trip in the operating room from p | ...
- Orthobond Received FDA De Novo Approval for Antibacterial Technology
Orthobond received on April 5th de novo approval for the company’s spinal fusion device with quaternary ammonium compound coating. Orthobond’s antibacterial treatment, Ostaguard™, covalently bonds its ...
- Best OnePlus 10 Pro cases
Some cases even bring added functionality, like a kickstand for propping up the OnePlus 10 Pro or antimicrobial coating to fight off bacteria in addition to withstanding drops. Whatever your ...
Go deeper with Bing News on:
Copper nanowire antimicrobial coating
- Coating Iron with Copper
Bucklin, of Troy, N. Y., for a new and improved mode of coating iron with copper, which promises to be an invention of no small importance to the arts. It has long been a desideratum to coat iron ...
- A catalyst for converting carbon dioxide, the main cause of global warming, into ethylene using vitamin C
The research team synthesized vitamin C with graphene quantum dots and fabricated a "vitamin C boosting copper nanowire" by combining the synthesized material with copper. This approach helped ...
- PPG Introduces Copper-Free Antifouling Coating NEXEON 810
PPG Industries Inc. PPG has launched PPG NEXEON 810, a novel copper-free antifouling coating designed with a strong emphasis on vessel performance, emission reduction and sustainability.
- PPG Introduces Copper-Free Antifouling Coating NEXEON 810
PPG Industries Inc. PPG has launched PPG NEXEON 810, a novel copper-free antifouling coating designed with a strong emphasis on vessel performance, emission reduction and sustainability. Independent ...
- Copper Coating 3D Prints
Using a process known as mechanical plating or peen plating, he deposits a layer of copper on a PLA print. The results look good, as you can see in the video below. This isn’t electroplating ...