Suppose you could replace “Made in China” with “Made in my garage.”
Suppose also that every time you polished off a jug of two percent, you would be stocking up on raw material to make anything from a cell phone case and golf tees to a toy castle and a garlic press.
And, you could give yourself a gold medal for being a bona fide, recycling, polar-bear-saving rock star.
Michigan Technological University’s Joshua Pearce is working on it. His main tool is open-source 3D printing, which he uses to save thousands of dollars by making everything from his lab equipment to his safety razor.
Using free software downloaded from sites like Thingiverse, which now holds over 54,000 open-source designs, 3D printers make all manner of objects by laying down thin layers of plastic in a specific pattern. While high-end printers can cost many thousands of dollars, simpler open-source units run between $250 and $500—and can be used to make parts for other 3D printers, driving the cost down ever further.
“One impediment to even more widespread use has been the cost of filament,” says Pearce, an associate professor of materials science and engineering and electrical and computer engineering. Though vastly less expensive than most manufactured products, the plastic filament that 3D printers transform into useful objects isn’t free.
Milk jugs, on the other hand, are a costly nuisance, either to recycle or to bury in a landfill. But if you could turn them into plastic filament, Pearce reasoned, you could solve the disposal problem and drive down the cost of 3D printing even more.
So Pearce and his research group decided to make their own recycling unit, or RecycleBot. They cut the labels off milk jugs, washed the plastic, and shredded it. Then they ran it through a homemade device that melts and extrudes it into a long, spaghetti-like string of plastic. Their process is open-source and free for everyone to make and use at Thingiverse.com.
The process isn’t perfect. Milk jugs are made of high-density polyethylene, or HDPE, which is not ideal for 3D printing. “HDPE is a little more challenging to print with,” Pearce says. But the disadvantages are not overwhelming. His group made its own climate-controlled chamber using a dorm-room refrigerator and an off-the-shelf teddy-bear humidifier and had good results. With more experimentation, the results would be even better, he says. “3D printing is where computers were in the 1970s.”
The Latest Bing News on:
RecycleBot
- RecycleBot Challenge announces winnerson April 22, 2024 at 12:28 pm
The winners for the 2024 RecycleBot Challenge have been unveiled. Embracing the spirit of "Earth Month'' this April, Keep Rutherford County Beautiful (KRCB) invited third graders across Rutherford ...
The Latest Google Headlines on:
RecycleBot
[google_news title=”” keyword=”RecycleBot” num_posts=”10″ blurb_length=”0″ show_thumb=”left”] [/vc_column_text]The Latest Bing News on:
3d printing feedstock
- UMaine’s novel polymer 3D printer surpasses former Guinness World Recordon April 26, 2024 at 6:03 pm
Four times larger than its predecessor, FoF 1.0 offers new opportunities in composite materials, including development of recycled and bio-based materials.
- Makers of the world’s largest 3D printer just beat their own recordon April 26, 2024 at 10:43 am
After a five-year reign, the world’s largest 3D printer located at the University of Maine has been usurped—by a newer, larger 3D printer developed at the same school.
- This is the world's largest 3D printer: The University of Maine breaks its own recordon April 26, 2024 at 8:42 am
Forward-looking: The University of Maine has broken its own 2019 Guinness World Record with a next-gen polymer 3D printer that is four times the size of its predecessor. Dubbed Factory of the Future 1 ...
- The world’s largest 3D printer is at a university in Maine. It just unveiled an even bigger oneon April 26, 2024 at 8:33 am
The university that boasts the world’s largest 3D printer developed one even bigger. A printer unveiled Tuesday at the University of Maine is four times larger than the current one and is capable of ...
- World's biggest 3D printer whirs into actionon April 26, 2024 at 7:09 am
A giant 3D printer, which is big enough to make a house, has been unveiled at the University of Maine. The university says it has beaten its own record for the world's largest polymer 3D printer - ...
- TOMRA Partners with OMV and Borealis to Close Plastic Recycling Gapson April 26, 2024 at 6:09 am
TOMRA, in collaboration with OMV and Borealis, is advancing plastic recycling by supplying high-quality raw materials from mixed post-consumer pl ...
- AMGTA research explores sustainability of metal additive manufacturing feedstockon April 25, 2024 at 3:11 am
The study was conducted with Syntec Associates and Divergent Technologies to determine specific energy requirements for producing metal 3D printing materials via three key processes.
- Sustainable Methods for Metal AM Feedstock Production Revealed in Research Studyon April 24, 2024 at 12:20 pm
The AMGTA unveils key findings on the energy efficiency of metal AM feedstock processing approaches, shedding light on sustainable manufacturing practices in the additive ...
- Neste RE™: Revolutionizing Plastics Manufacturing with Renewable and Recycled Feedstockon April 23, 2024 at 4:43 am
Neste, a global leader in renewable fuels and sustainable feedstock, is showcasing its Neste RE™ feedstock at Chinaplas 2024 in Shanghai. Neste ...
- Meltio introduces new robotic DED metal additive manufacturing solution alongside FANUC America & Accufactureon April 22, 2024 at 2:56 am
Meltio has introduced the Alchemist 1 all-in-one additive manufacturing robotic workcell in collaboration with FANUC America and Accufacture.
The Latest Google Headlines on:
3d printing feedstock
[google_news title=”” keyword=”3d printing feedstock” num_posts=”10″ blurb_length=”0″ show_thumb=”left”]