Joining carbon fiber composites and aluminum for lightweight cars and other multi-material high-end products could become less expensive and the joints more robust because of a new method that harnesses a laser’s power and precision.
The process, developed by a team led by Adrian Sabau of the Department of Energy’s Oak Ridge National Laboratory, would replace the practice of preparing the surface of the materials by hand using abrasive pads, grit blasting and environmentally harmful solvents. Using a laser to remove layers of material from surfaces prior to bonding improves the performance of the joints and provides a path toward automation for high-volume use.
“Our technique is vastly superior to the conventional surface preparation methods,” Sabau said. “Combined with the potentially dramatic reduction in the cost of carbon fiber polymer composites, this represents an important step toward increasing the use of this lightweight high-strength material in automobiles, which could reduce the weight of cars and trucks by 750 pounds.”
The surface treatment of aluminum and carbon fiber polymer composite is a critical step in the adhesive joining process, which directly affects the quality of bonded joints. Aluminum surfaces typically contain oils and other contaminants from production rolling operations while carbon fiber surfaces often contain mold releases.
“These surface contaminants affect surface energies and the quality of adhesion, so it is critical that they are removed,” said Sabau, adding that the laser also penetrates into the top resin layer, leaving individual carbon fibers exposed for direct bonding to the adhesive and increasing the surface area for better adhesion.
Test results support Sabau’s optimism as single-lap shear joint specimens showed strength, maximum load and displacement at maximum load were increased by 15 percent, 16 percent and 100 percent, respectively, over those measured for the baseline joints. Also, joints made with laser-structured surfaces can absorb approximately 200 percent more energy than the conventionally prepared baseline joints, researchers reported.
Sabau noted that the process also doubles the energy absorption in the joints, which has implications for crash safety and potential use in armor for people and vehicles. Tim Skszek of Magna International (Troy, Michigan), a project partner, shares Sabau’s enthusiasm.
“The results are most encouraging, enabling the automated processing of a multi-material carbon fiber-aluminum joint,” Skszek said. “With this work, we were able to focus on addressing the gaps in technology and commercial use, and we look forward to applying these findings to products.”
Learn more: Laser treatment, bonding potential road to success for carbon fiber
The Latest on: Carbon fiber composites
[google_news title=”” keyword=”carbon fiber composites” num_posts=”10″ blurb_length=”0″ show_thumb=”left”]
via Google News
The Latest on: Carbon fiber composites
- Dick Rutan, Who Flew Around the World Without Refueling, Dies at 85on May 8, 2024 at 1:14 pm
The advent of a new material, composites of carbon fiber, made it possible for the first time to imagine an airplane light enough for a round-the-world flight on a single tank of gas, Burt Rutan told ...
- Purdue, Wabash National collaborate on composite trailer that recaptures its own energyon May 8, 2024 at 12:18 pm
An experimental trailer that harvests its own electricity is anticipated to make trailers more sustainable and energy-efficient.
- North America Leads Carbon Mold Consumption, Emerging Economies on the Riseon May 8, 2024 at 6:52 am
The global carbon mold market is anticipated to reach a valuation of US$ 304.21 million in 2023 and is projected to accumulate over US$ 694.18 million by 2033 while securing a CAGR of 8.6% during the ...
- EQS-News: SGL Carbon: Focus on global growth trends pays offon May 7, 2024 at 6:30 pm
Composite Solutions has maintained considerable profitability ... weak demand from the wind industry and the associated capacity adjustment in the carbon fiber business. In addition, there was ...
- Aerospace Composites Market worth $52.1 billion by 2029 - Exclusive Report by MarketsandMarketson May 7, 2024 at 5:00 am
CHICAGO, May 7, 2024 /PRNewswire/ -- The report "Aerospace Composites Market by Fiber Type (Glass Fiber, Carbon Fiber, Ceramic Fiber), Matrix Type (Polymer Matrix Composite, Metal Matrix Composite, ...
- Aerospace Composites Market worth $52.1 billion by 2029 - Exclusive Report by MarketsandMarkets™on May 7, 2024 at 2:00 am
Matrix Type (Polymer Matrix Composite, Metal Matrix Composite, Ceramic Matrix Composite), Manufacturing Process, Aircraft Type, Applications & Region - Forecast to 2029", is estimated at USD 29.1 ...
- Jilin Chemical Fiber Group and Comac have signed a cooperation agreementon May 6, 2024 at 5:13 am
Tan Wangeng, deputy secretary of the party committee of Comac said during the signing ceremony: "Jilin Chemical Fiber Group has outstanding advantages in the carbon fiber industry chain and is ...
- Composite Rollers Market Projected to Grow at 7.6% CAGR, Reaching USD 297.4 Million by 2033on May 6, 2024 at 2:28 am
The composite rollers market is anticipated to expand its roots at a steady CAGR of 7.6% between 2023 and 2033. The market is expected to have a market share of USD 297.4 million by 2033 while it is ...
- People in composites: April 2024on April 30, 2024 at 9:32 am
TFP Hydrogen Products, Airbus SE, TPI Composites, IDI Composites International and Integrated Graphene announce new personnel and retirements.
- Landrum to see carbon fiber bike manufacturing near Saluda Grade Rail Trail, what to knowon April 27, 2024 at 3:40 am
Another carbon fiber bicycle element manufacturer is headed for the Saluda Grade Rail Trail. During the Criterium bike race on Friday, April 26, Boyd Cycling announced they would bring Munich ...
via Bing News