Cover of ACS Applied Energy Materials depicting a catalyst-modified solar cell producing hydrogen fuel under varying lighting conditions.
The Department of Energy’s Oak Ridge National Laboratory researchers have designed and additively manufactured a first-of-its-kind aluminum device that enhances the capture of carbon dioxide emitted from fossil fuel plants and other industrial processes.
Solutions for reducing global emissions of heat-trapping greenhouse gases such as CO2 address the continued use of low-cost, domestic fossil fuel resources while mitigating potential climate impacts.
ORNL’s device focuses on a key challenge in conventional absorption of carbon using solvents: the process typically produces heat that can limit its overall efficiency. By using additive manufacturing, researchers were able to custom design a multifunctional device that greatly improves the process efficiency by removing excess heat while keeping costs low.
Absorption, one of the most commonly used and economical methods for capturing CO2, places a flue-gas stream from smokestacks in contact with a solvent, such as monoethanolamine, known as MEA, or other amine solutions, that can react with the gas.
The team tested the novel circular device, which integrates a heat exchanger with a mass-exchanging contactor, inside a 1-meter-tall by 8-inch-wide absorption column consisting of seven commercial stainless-steel packing elements. The 3D-printed intensified device was installed in the top half of the column between the packing elements.
Additive manufacturing made it possible to have a heat exchanger within the column, as part of the packing elements, without disturbing the geometry, thus maximizing the contact surface area between the gas and liquid streams.
“We call the device intensified because it enables enhanced mass transfer (the amount of CO2 transferred from a gas to a liquid state) through in-situ cooling,” said Costas Tsouris, one of ORNL’s lead researchers on the project. “Controlling the temperature of absorption is critical to capturing carbon dioxide.”
When CO2 interacts with the solvent, it produces heat that can diminish the capability of the solvent to react with CO2. Reducing this localized temperature spike in the column through cooling channels helps increase the efficiency of CO2 capture.
“Prior to the design of our 3D printed device, it was difficult to implement a heat exchanger concept into the CO2 absorption column because of the complex geometry of the column’s packing elements. With 3D printing, the mass exchanger and heat exchanger can co-exist within a single multifunctional, intensified device,” said ORNL’s Xin Sun, the project’s principal investigator.
Embedded coolant channels were added inside the packing element’s corrugated sheets to allow for heat exchange capabilities. The final prototype measured 20.3 centimeters in diameter, 14.6 centimeters in height, with a total fluid volume capacity of 0.6 liters. Aluminum was chosen as the initial material for the intensified device because of its excellent printability, high thermal conductivity, and structural strength.
“The device can also be manufactured using other materials, such as emerging high thermal conductivity polymers and metals. Additive manufacturing methods like 3D printing are often cost-effective over time because it takes less effort and energy to print a part versus traditional manufacturing methods,” said Lonnie Love, a lead manufacturing researcher at ORNL, who designed the intensified device.
The prototype demonstrated that it was capable of substantially enhancing carbon dioxide capture with the amine solution, which was chosen because its highly reactive to CO2. In results published in the AIChE Journal, ORNL researchers conducted two separate experiments — one that varied the CO2-containing gas flow rate and one that varied the MEA solvent flow rate. The experiments aimed to determine which operating conditions would produce the greatest benefit to carbon capture efficiency.
Both experiments produced substantial improvements in the carbon capture rate and demonstrated that the magnitude of the capture consistently depended on the gas flow rates. The study also showed a peak in capture at 20% of carbon dioxide concentration, with percent of increase in capture rate ranging from 2.2% to 15.5% depending on the operating conditions.
“The success of this 3D printed intensified device represents an unprecedented opportunity in further enhancing carbon dioxide absorption efficiency and demonstrates proof of concept,” Sun said.
Future research will focus on optimizing operating conditions and device geometry to produce additional improvements in the carbon capture absorption process.
The Latest Updates from Bing News & Google News
Go deeper with Bing News on:
Carbon dioxide capture
- Feds defend carbon capture technology as Alberta project gets cancelled over cost
"Carbon capture and sequestration technologies are getting better ... Canada had captured and stored a total of 7.2 million tonnes of carbon dioxide since 2017, most of it at Shell Canada's Quest CCS ...
- High hopes for carbon capture, underground storage
Capturing carbon dioxide (CO2) from the atmosphere to store underground "sounds too good to be true", a climate expert told AFP, yet the technology to increase its capacity tenfold is already being ...
- XPRIZE’s $100-Million Carbon-Removal Contest Selects Finalists
A competition to develop carbon-removal technology that is run by XPRIZE and backed by money from Elon Musk has announced 20 finalists. A winner will be announced next year ...
- World's largest direct air capture plant starts sucking CO2 from the sky
marking an important milestone in the world’s emerging efforts to remove planet-warming carbon dioxide from the atmosphere and permanently lock it away. The plant’s opening also helps lay the ...
- The world’s largest carbon removal plant is here, and bigger ones are on the way
A big new facility built to take carbon dioxide out of the atmosphere opened up in Iceland. It’s a stepping stone to bigger plans in the US.
Go deeper with Google Headlines on:
Carbon dioxide capture
[google_news title=”” keyword=”carbon dioxide capture” num_posts=”5″ blurb_length=”0″ show_thumb=”left”]
Go deeper with Bing News on:
3D printed intensified device
- Researchers harness blurred light to 3D-print high-quality optical components
Canadian researchers have developed a new 3D printing method called blurred tomography that can rapidly produce microlenses with commercial-level optical quality. The new method may make it easier and ...
- The Best 3D Printers for 2024
More affordable than ever, 3D printers are booming for personal, professional, and educational use. Here's everything to know before you buy one, along with the top models from our hands-on testing.
- An ink for 3D-printing flexible devices without mechanical joints
Researchers are targeting the next generation of soft actuators and robots with an elastomer-based ink for 3D printing objects ... on soft robotics or wearable devices, keeping things light ...
- An ink for 3D-printing flexible devices without mechanical joints
(Nanowerk News) For engineers working on soft robotics or wearable devices, keeping things light is a constant ... The research has been published in the journal Advanced Materials ("3D Printing of ...
- 3D-printed PEEK-based Cranial Implants Cleared by FDA
Designed for use in hospitals. The 3D printer’s cleanroom-based architecture combined with simplified post-processing workflows makes it an ideal technology for producing patient-specific medical ...
Go deeper with Google Headlines on:
3D printed intensified device
[google_news title=”” keyword=”3D printed intensified device” num_posts=”5″ blurb_length=”0″ show_thumb=”left”]