Printed nozzle system could make uniform, versatile fibers at much lower cost
Meshes made from fibers with nanometer-scale diameters have a wide range of potential applications, including tissue engineering, water filtration, solar cells, and even body armor. But their commercialization has been hampered by inefficient manufacturing techniques.
In the latest issue of the journal Nanotechnology, MIT researchers describe a new device for producing nanofiber meshes, which matches the production rate and power efficiency of its best-performing predecessor — but significantly reduces variation in the fibers’ diameters, an important consideration in most applications.
But whereas the predecessor device, from the same MIT group, was etched into silicon through a complex process that required an airlocked “clean room,” the new device was built using a $3,500 commercial 3-D printer. The work thus points toward nanofiber manufacture that is not only more reliable but also much cheaper.
The new device consists of an array of small nozzles through which a fluid containing particles of a polymer are pumped. As such, it is what’s known as a microfluidic device.
“My personal opinion is that in the next few years, nobody is going to be doing microfluidics in the clean room,” says Luis Fernando Velásquez-García, a principal research scientist in MIT’s Microsystems Technology Laboratories and senior author on the new paper. “There’s no reason to do so. 3-D printing is a technology that can do it so much better — with better choice of materials, with the possibility to really make the structure that you would like to make. When you go to the clean room, many times you sacrifice the geometry you want to make. And the second problem is that it is incredibly expensive.”
Velásquez-García is joined on the paper by two postdocs in his group, Erika García-López and Daniel Olvera-Trejo. Both received their PhDs from Tecnológico de Monterrey in Mexico and worked with Velásquez-García through MIT and Tecnológico de Monterrey’s nanotech research partnership.
Hollowed out
Nanofibers are useful for any application that benefits from a high ratio of surface area to volume — such as solar cells, which try to maximize exposure to sunlight, or fuel cell electrodes, which catalyze reactions at their surfaces. Nanofibers can also yield materials that are permeable only at very small scales, such as water filters, or that are remarkably tough for their weight, such as body armor.
Most such applications depend on fibers with regular diameters. “The performance of the fibers strongly depends on their diameter,” Velásquez-García says. “If you have a significant spread, what that really means is that only a few percent are really working. Example: You have a filter, and the filter has pores between 50 nanometers and 1 micron. That’s really a 1-micron filter.”
Because the group’s earlier device was etched in silicon, it was “externally fed,” meaning that an electric field drew a polymer solution up the sides of the individual emitters. The fluid flow was regulated by rectangular columns etched into the sides of the emitters, but it was still erratic enough to yield fibers of irregular diameter.
The new emitters, by contrast, are “internally fed”: They have holes bored through them, and hydraulic pressure pushes fluid into the bores until they’re filled. Only then does an electric field draw the fluid out into tiny fibers.
Beneath the emitters, the channels that feed the bores are wrapped into coils, and they gradually taper along their length. That taper is key to regulating the diameter of the nanofibers, and it would be virtually impossible to achieve with clean-room microfabrication techniques. “Microfabrication is really meant to make straight cuts,” Velásquez-García says.
Fast iteration
In the new device, the nozzles are arranged into two rows, which are slightly offset from each other. That’s because the device was engineered to demonstrate aligned nanofibers — nanofibers that preserve their relative position as they’re collected by a rotating drum. Aligned nanofibers are particularly useful in some applications, such as tissue scaffolding. For applications in which unaligned fibers are adequate, the nozzles could be arranged in a grid, increasing output rate.
Besides cost and design flexibility, Velásquez-García says, another advantage of 3-D printing is the ability to rapidly test and revise designs. With his group’s microfabricated devices, he says, it typically takes two years to go from theoretical modeling to a published paper, and in the interim, he and his colleagues might be able to test two or three variations on their basic design. With the new device, he says, the process took closer to a year, and they were able to test 70 iterations of the design.
“A way to deterministically engineer the position and size of electrospun fibers allows you to start to think about being able to control mechanical properties of materials that are made from these fibers. It allows you to think about preferential cell growth along particular directions in the fibers — lots of good potential opportunities there,” says Mark Allen, the Alfred Fitler Moore Professor at the University of Pennsylvania, with joint appointments in electrical and systems engineering and mechanical engineering and applied mechanics. “I anticipate that somebody’s going to take this technology and use it in very creative ways. If you have the need for this type of deterministically engineered fiber network, I think it’s a very elegant way to achieve that goal.”
Learn more:3-D-printed device builds better nanofibers
The Latest on: Nanofiber manufacturing
[google_news title=”” keyword=”nanofiber manufacturing” num_posts=”10″ blurb_length=”0″ show_thumb=”left”]- Fueling Advanced Manufacturing Growth Across Indiana’s Hardtech Corridor: Reimagine IN-MaC through Purdue in West Lafayette and Indianapolison April 28, 2024 at 8:17 am
To fuel and impact the ongoing manufacturing renaissance and expand its reach across Indiana, Purdue University in West Lafayette is launching an IN-MaC node at Purdue in Indianapolis (PIN) in a joint ...
- Manufacturing Newson April 26, 2024 at 1:28 pm
Showcase your company news with guaranteed exposure both in print and online What is really happening in the relationship between the world’s 2 largest economies… Who's the best of the best in ...
- Buffalo Manufacturing Newson April 26, 2024 at 6:42 am
National Fire Adjustment Co. Inc. Ranked by Local manufacturing employees Ranked by Barrels produced in 2021 Ranked by Local manufacturing employees Custom Maid, a premier provider of cleaning ...
- Here are the 30+ startups showcasing at HAX's May 1 Demo Dayon April 22, 2024 at 2:39 pm
A few weeks back, TechCrunch ventured out to New Jersey to pay an early visit to HAX’s Newark offices. HAX’s China operations have shrunk considerably since then, courtesy of a global pandemic and all ...
- Here are the 30+ startups showcasing at HAX’s May 1 Demo Dayon April 22, 2024 at 2:39 pm
Verdex has developed a highly scalable and eco-friendly nanofiber manufacturing process to produce advanced filtration materials. These materials can be used for energy efficient HVAC, CO 2 ...
- Intel Just Revealed Why It Can't Split From Its Manufacturing Model and Why the Stock Is a Hold at Beston April 14, 2024 at 9:10 pm
Intel just pulled back the curtain surrounding the steep losses in its manufacturing business. The company will need the ample funding it's getting from the E.U. and Washington to help it reach ...
- An Intelligent Future for Manufacturingon April 11, 2024 at 5:00 pm
Digitalisation plays a key role in the evolution of manufacturing industries. Foundry’s Digital Business Study 2023 shows that 93% of manufacturers surveyed have adopted or plan to adopt a ...
- Rational Design of Nanofiber Scaffolds for Orthopedic Tissue Repair and Regenerationon April 4, 2024 at 5:00 pm
By contrast, electrospinning can be used to generate nanofiber assemblies for mimicking the special fiber organizations in musculoskeletal tissues. Therefore, electrospun nanofiber scaffolds are ...
- US manufacturing on the mend; rising raw material prices pose obstacleon April 1, 2024 at 10:11 am
WASHINGTON, April 1 (Reuters) - U.S. manufacturing grew for the first time in 1-1/2 years in March as production rebounded sharply and new orders increased, but employment at factories remained ...
- US manufacturing activity grows at fastest rate since 2022on April 1, 2024 at 4:20 am
The US manufacturing sector is in its strongest position since 2022, two reports out Monday showed. The Institute for Supply Management's manufacturing PMI indicated the manufacturing sector moved ...
via Google News and Bing News