Techniques could lead to personalized wearable and implantable devices.
Hearing aids, dental crowns, and limb prosthetics are some of the medical devices that can now be digitally designed and customized for individual patients, thanks to 3-D printing. However, these devices are typically designed to replace or support bones and other rigid parts of the body, and are often printed from solid, relatively inflexible material.
Now MIT engineers have designed pliable, 3-D-printed mesh materials whose flexibility and toughness they can tune to emulate and support softer tissues such as muscles and tendons. They can tailor the intricate structures in each mesh, and they envision the tough yet stretchy fabric-like material being used as personalized, wearable supports, including ankle or knee braces, and even implantable devices, such as hernia meshes, that better match to a person’s body.
As a demonstration, the team printed a flexible mesh for use in an ankle brace. They tailored the mesh’s structure to prevent the ankle from turning inward — a common cause of injury — while allowing the joint to move freely in other directions. The researchers also fabricated a knee brace design that could conform to the knee even as it bends. And, they produced a glove with a 3-D-printed mesh sewn into its top surface, which conforms to a wearer’s knuckles, providing resistance against involuntary clenching that can occur following a stroke.
“This work is new in that it focuses on the mechanical properties and geometries required to support soft tissues,” says Sebastian Pattinson, who conducted the research as a postdoc at MIT.
Pattinson, now on the faculty at Cambridge University, is the lead author of a study published today in the journal Advanced Functional Materials. His MIT co-authors include Meghan Huber, Sanha Kim, Jongwoo Lee, Sarah Grunsfeld, Ricardo Roberts, Gregory Dreifus, Christoph Meier, and Lei Liu, as well as Sun Jae Professor in Mechanical Engineering Neville Hogan and associate professor of mechanical engineering A. John Hart.
Riding collagen’s wave
The team’s flexible meshes were inspired by the pliable, conformable nature of fabrics.
“3-D-printed clothing and devices tend to be very bulky,” Pattinson says. “We were trying to think of how we can make 3-D-printed constructs more flexible and comfortable, like textiles and fabrics.”
Pattinson found further inspiration in collagen, the structural protein that makes up much of the body’s soft tissues and is found in ligaments, tendons, and muscles. Under a microscope, collagen can resemble curvy, intertwined strands, similar to loosely braided elastic ribbons. When stretched, this collagen initially does so easily, as the kinks in its structure straighten out. But once taut, the strands are harder to extend.
Inspired by collagen’s molecular structure, Pattinson designed wavy patterns, which he 3-D-printed using thermoplastic polyurethane as the printing material. He then fabricated a mesh configuration to resemble stretchy yet tough, pliable fabric. The taller he designed the waves, the more the mesh could be stretched at low strain before becoming more stiff — a design principle that can help to tailor a mesh’s degree of flexibility and helped it to mimic soft tissue.
The researchers printed a long strip of the mesh and tested its support on the ankles of several healthy volunteers. For each volunteer, the team adhered a strip along the length of the outside of the ankle, in an orientation that they predicted would support the ankle if it turned inward. They then put each volunteer’s ankle into an ankle stiffness measurement robot — named, logically, Anklebot — that was developed in Hogan’s lab. The Anklebot moved their ankle in 12 different directions, and then measured the force the ankle exerted with each movement, with the mesh and without it, to understand how the mesh affected the ankle’s stiffness in different directions.
In general, they found the mesh increased the ankle’s stiffness during inversion, while leaving it relatively unaffected as it moved in other directions.
“The beauty of this technique lies in its simplicity and versatility. Mesh can be made on a basic desktop 3-D printer, and the mechanics can be tailored to precisely match those of soft tissue,” Hart says.
Stiffer, cooler drapes
The team’s ankle brace was made using relatively stretchy material. But for other applications, such as implantable hernia meshes, it might be useful to include a stiffer material, that is at the same time just as conformable. To this end, the team developed a way to incorporate stronger and stiffer fibers and threads into a pliable mesh, by printing stainless steel fibers over regions of an elastic mesh where stiffer properties would be needed, then printing a third elastic layer over the steel to sandwich the stiffer thread into the mesh.
The combination of stiff and elastic materials can give a mesh the ability to stretch easily up to a point, after which it starts to stiffen, providing stronger support to prevent, for instance, a muscle from overstraining.
The team also developed two other techniques to give the printed mesh an almost fabric-like quality, enabling it to conform easily to the body, even while in motion.
“One of the reasons textiles are so flexible is that the fibers are able to move relative to each other easily,” Pattinson says. “We also wanted to mimic that capability in the 3-D-printed parts.”
In traditional 3-D printing, a material is printed through a heated nozzle, layer by layer. When heated polymer is extruded it bonds with the layer underneath it. Pattinson found that, once he printed a first layer, if he raised the print nozzle slightly, the material coming out of the nozzle would take a bit longer to land on the layer below, giving the material time to cool. As a result, it would be less sticky. By printing a mesh pattern in this way, Pattinson was able to create a layers that, rather than being fully bonded, were free to move relative to each other, and he demonstrated this in a multilayer mesh that draped over and conformed to the shape of a golf ball.
Finally, the team designed meshes that incorporated auxetic structures — patterns that become wider when you pull on them. For instance, they were able to print meshes, the middle of which consisted of structures that, when stretched, became wider rather than contracting as a normal mesh would. This property is useful for supporting highly curved surfaces of the body. To that end, the researchers fashioned an auxetic mesh into a potential knee brace design and found that it conformed to the joint.
“There’s potential to make all sorts of devices that interface with the human body,” Pattinson says. Surgical meshes, orthoses, even cardiovascular devices like stents — you can imagine all potentially benefiting from the kinds of structures we show.”
The Latest on: 3D printing
via Google News
The Latest on: 3D printing
- 3D Printing in Automotive Market 2021 Competitive Insights – 3D Systems, GE, Stratasys, Exone, Hoganas, Voxeljeton January 12, 2021 at 6:30 am
D Printing in Automotive market will register a 11.2% CAGR in terms of revenue, the global market size will reach $ 791.4 million by 2025, from $ 517.5 million in 2019. Top Leading Companies of ...
- ExOne Launches Online Calculator for Manufacturers to Quickly Compare the Cost of Metal 3D Printing for Productionon January 12, 2021 at 5:07 am
The new ExOne Production Metal Cost Calculator provides manufacturers with a per-part estimate for binder jet 3D printing a precision metal part, so the technology can easily be compared to other ...
- CES 2021 Additive Intelligence drastically reduces the cost of metal 3D printing with AIon January 12, 2021 at 3:40 am
Additive Intelligence is drastically reducing the cost of mass-producing metal 3D printed parts by leveraging the power of AI. Our ...
- How 3D printing is helping CERN scientists upgrade the world's largest machineon January 12, 2021 at 2:12 am
Manufacturing tiny, highly complex components for the large hadron collider is no easy challenge. CERN scientists found a solution in 3D printing.
- Global 3D Printing Building Construction Market Opportunities and Strategies, 2019-2023, 2023-2025 & 2025-2030 - ResearchAndMarkets.comon January 12, 2021 at 1:53 am
The “3D Printing Building Construction Global Market Opportunities and Strategies to 2030: COVID-19 Growth and Change” report has been added to ResearchAndMarkets.com’s offering. 3D Printing Building ...
- 3D Printing in Medical Applications Market 2021 Growth Forecast Analysis by Manufacturers, Regions, Type and Application to 2025on January 11, 2021 at 2:20 pm
Global 3D Printing in Medical Applications Market (2021 -2025) status and position of worldwide and key regions, ...
- 4 3D Printing Stocks Leading the Fourth Industrial Revolutionon January 11, 2021 at 2:06 pm
The world is on the cusp of a fourth industrial revolution, and these four 3D printing stocks are among the best stocks to buy now. More From InvestorPlace Why Everyone Is Investing in 5G All WRONG ...
- Formlabs' new castable wax makes it easier to 3D-print jewelry moldson January 11, 2021 at 6:00 am
Formlabs is announcing a new version of its Castable Wax, that’s targeted toward jewelry designers and makers. Castable Wax 40 is, as the name implies, a 3D-printable resin made up of 40 percent wax, ...
- 3 Reinvigorated 3D Printing Stocks to Buy for Q1on January 8, 2021 at 12:05 pm
The once-overhyped, now-depressed 3D printing industry is finally ready to break out, and these are the best 3D printing stocks to own.
- Why 3D-Printing Stocks Soared Todayon January 7, 2021 at 4:31 pm
Shares of 3D-printing companies rose sharply on Thursday after 3D Systems reported blockbuster preliminary results for the fourth quarter. The company said that it ...
via Bing News